Filetype PDF | Posted on 29 Jan 2023 | 3 years ago
Authentication
digital resources
385x Filetype PDF File size 1.21 MB Source: www.modcon-systems.com
IL
O
E MOD-4100 S
D
U ON-LINE SALT
R
C IN CRUDE OIL ANALYZER
N
I On-line measurement of the salt concentration in crude oil plays an important role in the
T crude oil chain, from the well head until entering the crude distillation unit. The MOD-4100 S
L is an on-line salt in crude oil analyzer, which is designed to provide real time analytical data of
A
the salt content in crude oils. Its technology is based on ASTM D 3230, an electrometric
method. This method determines the salt concentration in crude oil by measuring its
conductivity, when dissolved in a mixture of an aromatic and an alcoholic solvent.
MEASUREMENTS
4100 S S
- SALT CONTENT IN CRUDE OIL (PTB or mg/L)
D
O ADVANTAGES
M Provides online critical data of crude oil qualities
Provides on-line data about the salt content at the
oil-well head
Provides on line data of the salt content prior and
after shipment
Provides on-line data of the salt content prior and
after blending
Provides on-line data of the salt content before
entering the desalter
Indicates the desalter efficiency.
Allows on-line optimization of the desalter
process conditions.
Reduces water, chemicals and energy consumption in the desalters.
On-Line information of the salt content of crude oil crude oil entering the CDU
Reduces Corrosion, preventing plugging and fouling of pipelines.
On-Line information of the salt content of crude oil crude oil entering the CDU
Reduces Corrosion, preventing plugging and fouling of pipelines.
info@modcon-systems.com www.modcon-systems.com
L
I
E O
D
SALT IN CRUDE OIL
U
Crude oils and crude oil blends have
CR Incorporation of the MOD 4100 S
different physical and chemical
N before, between and after the desalters
properties, which depend primarily
provides an effective tool to operate the
I
on their place of origin. Even if
desalter at maximum efficiency and at
T
originated from the same location,
lowest cost to reduce the salt content to
L
fluctuations in physical properties are a
its minimum, before the crude oil enters
common phenomenon. Several quality
SA into the CDU.
properties have impact on the cost and
the ability to process the crude oils in
0 S
certain refineries, among these the salt
content. On line information of the salt
410 concentration in crude oil is critical to
- prevent corrosion, fouling and plugging
of the pipelines and production units of
D the refinery.
MO
\ The importance of measuring on-line the
salinity of crude oil is not restricted to
the refinery operation only, but is also
essential from a commercial point of
view.
The salt content in crude oil is one of the
parameters that will influence the crude
oil quality and by that, its commercial
value.
The MOD 4100 S is an on-line salt in The MOD 4100 S enables to check the
salt in crude quality before and after
crude oil process analyzer, which is
loading and unloading, during
designed to provide real time analyses
transportation from the oil-well to the
of the salt concentration in crude oils,
terminals, during shipment and during
expressed in PTB or mg/l. Its technology
transportation from the terminals and
is based on a wet chemical
electrometric conductivity method. tank-farms to the refineries.
info@modcon-systems.com 2 www.modcon-systems.com
E
D ANALYSER PRINCIPLE AND USER BENEFIT
U
R
IL
C
Error messages will be displayed in any case
The MOD 4100 S salt in crude analyzer has
N
O of a faulty status .
been designed to perform quantitative
E I
analyses of the salt concentration in crude
T
D
L oils. Samples can be taken from vessels, pipes
U
A vessels, bypasses or pressure pipes.
Based on ASTM D 3230, the MOD 4100 S
R
According to that a sampling system is
applies a wet chemical electrometric
designed to feed the analyzer with a sample
method, which determines the salt
S C
at optimized conditions, and to guarantee
A concentration of crude oils through
measuring its conductivity in solution. the provision of precise analytical results.
R
4100 S S
E
- Users Benefit
4100 Z Measurement Procedures
D Y
D L
O The MOD 4100 S provides a high
The analytical procedure starts with
A quality salt analyses
sampling of the process stream and
M
N
MO
bringing a well defined quantity of the
A sample into the analyzer’s measuring cell. Correlates with ASTM D3230
ATEX Eex d
This is fully automatically and accurately
performed by an electronic system that
controls a set of precise pumps and valves. Low Maintenance
Short term ROI
An accurate amount of a sample of crude
oil is brought into the measuring cell.
Precise volumes of solvents are accurately
added to the cell content and mixed with Options
the sample.
The analyzer can be provided to cover the
The salt concentration is determined by range of 0-150 PTB or of 0-400 PTB
measuring the conductivity of a the crude
oil sample dissolved sample in fixed amount
of diluents.
The analyzer is designed to operate indoors.
For extreme cold or hot ambient
When the measurement are terminated,
temperatures the analyzer can be provided
the cell content is discarded, and the
in a heated or cooled environmental
system flushes rinses and cleans itself enclosure as well.
automatically.
info@modcon-systems.com 3 www.modcon-systems.com
E
D
U
R TECHNICAL SPECIFICATION
C
Measuring Principle Electrometric
Method based on ASTM D-3230
IN
T Detector conductivity cell
L
Solvents (as per ASTM) Solvent – Xylene
Solvent Mixture - Absolute Methanol/n-Butanol ,
SA Cleaning Solution – Naphtha
Optional according to customer specification configurable) within rages of
Measurement range 0-150 PTB or 0-450 mg/l or
0-400 PTB or 0-1000mg/l
4100 S Response time <= 6 min
-
Accuracy Correlates to ASTM D 3230
D Repeatability +/- 2% FS
Display Display 7”
MO Power supply 230 VAC, 50Hz
Power consumption 1.3 KVA
Output 2 isolated 4-20 mA, free configurable
Optional:, RS485, Modbus RTU, Ethernet
Alarm – Signal Hi/Low free programmable.
optional Up to 2 alarms
230VAC /50Hz/1Amps, Dry contact
Alarm - Error Activated by device error
1 contact ; 230VAC/50Hz/1Amps, Dry contact
Ambient Temp. 5 – 35 degree °C
Sample inlet pressure 4-16 Bar
Gravity outlet, atmospheric to drain
Sample discharge Optional sample recovery system available
4-8 bar
Instrument Air Less than 20 l/hr
Clean and dry instrument grade 4.1 bar minimum
Sample Temperature 10 - 60 °C
ATEX Zone 1 ATEX Eex d II B+ H2 T4 Gc
Weight Analyzer 440 Kg
Dimensions of analyzer WxHxD = 980 x 1800 x 800
SYSTEMS LTD
Registered in England and Wales with company number 07794530
10 Orange St., Haymarket London WC2H 7DQ
United Kingdom
Phone / Fax+44-207-5043626
info@modcon-systems.com 4 www.modcon-systems.com
no reviews yet
Please Login to review.
